Skip to content

MoldMarketNews

Mold Industry Insights, Injection Molding Knowledge & Tooling Guides

Menu
  • Home
  • About Us
  • Mold Market Insights
  • Injection Molding
    • Injection Molding Basics
    • Plastic Injection Molds
    • Molding Process
    • Molding Defects
    • Process Troubleshooting
  • Mold Design
    • DFM & Part Design
    • Mold Structure & Components
    • Gate, Cooling & Mold Flow
  • Mold Manufacturing
    • Mold Making Process
    • Machining Methods
    • Mold Trial & Quality
  • Tooling Materials
    • Mold Steel & Heat Treatment
    • Plastic Materials
    • Surface Finish & Tolerances
  • Mold Maintenance
    • Cleaning & Preventive Care
    • Repair & Troubleshooting
    • Storage & Service Life
  • Buyer Guides
Menu

Category: Mold Maintenance

Learn mold maintenance methods, injection mold cleaning, tooling repair, preventive maintenance, storage tips and ways to extend mold service life.

How Does Resin Type Affect Mold Storage Protection

Posted on 2026-11-20

Mold storage is usually treated as routine upkeep. Teams clean the tool, dry it and apply protective oil before putting it away. The resin that ran in the previous job can change...

How Can Vent Clogging Be Distinguished From Poor Filling

Posted on 2026-11-13

A short shot on a molded part rarely announces its cause. Missing edges, short corners, shallow sections, and unfinished ribs can come from a melt that never had the flow to get...

Why Does Shot Count Matter More Than Calendar Age for Mold Life

Posted on 2026-11-06

Picture two molds bought in the same year. One has run through several demanding campaigns. The other has mostly sat on a rack, pulled out now and then for a short batch....

How Does Ultrasonic Cleaning Affect Mold Components

Posted on 2026-10-30

A mold can look clean from the outside while residue remains packed around ejector pins, trapped inside narrow vents, or spread across small grooves in a cavity insert. During repeated production cycles,...

How Does Resin Residue Cause Repeated Mold Defects

Posted on 2026-10-23

Resin residue inside an injection mold can cause a defect that comes and goes with no obvious pattern. One cycle gives a clean part. The next shows a dull patch or a...

Why Do Mold Cooling Channels Matter During Long Storage

Posted on 2026-10-16

Cooling channels do their job by moving water through passages inside the mold to manage heat during production. Once that production stops for a while, these internal passages tend to get far...

How Does Mold Storage Humidity Affect Tool Life

Posted on 2026-10-09

Where Does Moisture Come From During Mold Storage? Molds spend plenty of time doing nothing between production runs, during maintenance windows, or just waiting for the next order to come in. Sitting...

Why Does Flash Appear After Mold Alignment Changes

Posted on 2026-10-02

Flash can appear after mold alignment work even when the molding conditions have not changed. A thin edge of material may suddenly remain around the parting line, near an insert area, or...

How to Clean Injection Molds Properly

Posted on 2026-09-25

Anyone who has run injection molding equipment for a while has probably noticed the same pattern: a mold that produces flawless parts for months suddenly starts showing minor surface marks, incomplete fills,...

Why Mold Maintenance Matters in Production

Posted on 2026-07-10

Walk onto almost any factory floor and ask someone how their molds are doing, and you will probably get a shrug. "Fine, I think." That answer says a lot. Molds rarely announce...

Recent Posts

  • How Does Resin Type Affect Mold Storage Protection
  • How Can Vent Clogging Be Distinguished From Poor Filling
  • Why Does Shot Count Matter More Than Calendar Age for Mold Life
  • How Does Ultrasonic Cleaning Affect Mold Components
  • How Does Resin Residue Cause Repeated Mold Defects

Archives

  • November 2026
  • October 2026
  • September 2026
  • August 2026
  • July 2026

Categories

  • Mold Maintenance
    • Storage & Service Life
    • Repair & Troubleshooting
    • Cleaning & Preventive Care
  • Tooling Materials
    • Surface Finish & Tolerances
    • Plastic Materials
    • Mold Steel & Heat Treatment
  • Mold Manufacturing
    • Mold Making Process
  • Mold Design
    • DFM & Part Design
  • Injection Molding
    • Injection Molding Basics
  • Mold Market Insights

Powered by MoldMarketNews © 2026

©2026 MoldMarketNews